Now Reading: Motorola Moto G Stylus 2020 XT2043 Camera Lens Glass & Back Cover Replacement Guide | DIY Repair
-
01
Motorola Moto G Stylus 2020 XT2043 Camera Lens Glass & Back Cover Replacement Guide | DIY Repair
Motorola Moto G Stylus 2020 XT2043 Camera Lens Glass & Back Cover Replacement Guide | DIY Repair
Hi everyone, Welcome back to Geardo
Today, we will show you how to replace the camera lens glass on the Motorola Moto G Stylus (2020) mobile phone.
If your camera lens is scratched, cracked, or affecting image quality, replacing just the lens glass is a cost-effective way to restore your phone’s camera performance without replacing the entire module.
This guide is written in a beginner-friendly format, so even if you have no prior repair experience, you can follow along step by step.
Before starting, make sure you have the proper tools ready.
Repair Difficulty
Repair Difficulty: ⭐⭐⭐☆☆ (Moderate)
Estimated Time: 25–40 minutes
Device Type: Smartphone
Repair Type: Camera Lens Glass Replacement
easons for Camera Lens Replacement
- Cracked or shattered camera glass
- Blurry or foggy photos
- Scratches affecting image clarity
- Dust entering the camera module
- Cosmetic damage around the camera area
Check The Latest Motorola Phones are in Clearance “up to 60% off” – https://amzn.to/480ho0w
Before You Begin
Compatibility and Model Numbers
- Motorola Moto G Stylus (2020)
Model Numbers | XT2043, XT2043-4
Tools Required
- Mobile phone heating pad or hairdryer/heat gun
- Plastic pry tool / card pry
- Suction cups
- Phillips #00/#000 screwdrivers
- Torx T3 / T4 / T5 Screwdriver (Depends on the version)
- Flathead Screwdriver
- Tweezers (for connectors)
- B7000 glue or double-sided adhesive (for back cover)
- Rubber bands or bonding clips to secure the back cover
Using proper tools reduces the risk of damaging the phone.
How to Find Tools and Parts
- Heating pad – https://amzn.to/3H0tHzJ
- Portable Heat Gun – https://amzn.to/4mszih1
- Clamps https://amzn.to/3GYJT4w
- STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
- Glue | Adhesive https://amzn.to/46exVxe
- Compatible Parts –
- Battery – https://amzn.to/499v2jk
- Screen – https://amzn.to/47HnpOv
- Other Parts – https://amzn.to/4hO2wG5
- Silicone Work Repair Mat https://amzn.to/45Emz5l
Step-by-Step Repair Guide
Step 1: Heat the Back Cover
First, take out the back cover from the body.
To remove it safely, gently heat around the edges of the rear cover until the adhesive softens.
You can use:
- Heating pad (recommended)
- Heat gun
- Hairdryer
Place the phone on the heating pad with the back facing down and allow it to heat evenly.
Step 2: Create an Opening
Use a suction cup to lift a small gap between the back cover and the frame.
Insert a plastic card or pry tool and carefully slide it around the edges to cut through the adhesive.
Step 3: Remove the Back Cover
Hold near the fingerprint (touch ID) area and gently pull the back cover away from the body.
Remove it completely and set it aside.
Step 4: Remove Screws and Frame
Undo the nine screws securing the logic board frame.
Carefully remove the frame along with the camera lens housing.
Step 5: Remove the Broken Lens
Take out the damaged lens glass from the frame.
This model has two lens rings, so identify which one needs replacement.
Apply slight heat to the lens area and push from the rear side to remove it.
If the lens is heavily cracked, carefully remove it piece by piece.
Step 6: Clean the Surface
Clean the lens area thoroughly to remove dust, glue residue, or broken glass particles.
This step is important to ensure proper installation and clear camera quality.
Step 7: Install New Lens Glass
Place the new camera lens glass into position.
Apply adhesive if needed and ensure it sits perfectly aligned.
You can repeat the same process for the second lens if required.
Step 8: Reassemble the Frame
Place the logic board frame back into position.
Secure it using the nine screws removed earlier.
Step 9: Reattach the Back Cover
Before reinstalling:
- Check if the back cover adhesive is still usable
- If not, apply B7000 glue or new double-sided adhesive
Press the back cover firmly into place.
Step 10: Secure the Device
Use bonding clips or rubber bands to hold the phone tightly while the adhesive sets.
Leave it for some time to ensure proper sealing.
❓ FAQ (Frequently Asked Questions)
Q1: Can I replace only the camera lens glass?
Yes, you can replace just the lens glass without changing the full camera module.
Q2: Will this fix blurry photos?
If the blur is caused by scratches or cracks on the lens glass, yes.
Q3: Is heating necessary?
Yes, heating softens adhesive and prevents damage during removal.
Q4: What if the lens breaks into pieces?
Remove it carefully piece by piece using tweezers.
Q5: Do I need glue for installation?
Yes, adhesive ensures the new lens stays securely in place.
🔧 Troubleshooting
Q1: Camera still blurry after replacement
Make sure the lens area is clean and free of dust before installation.
Q2: Lens not fitting properly
Check alignment and ensure you are using the correct lens ring.
Q3: Back cover not sticking
Apply fresh adhesive or B7000 glue and secure with clips.
Q4: Dust inside the camera
Open the device again and clean the area before sealing.
Q5: Lens falls off after repair
This indicates insufficient adhesive—reapply glue properly.
📌 Final Thoughts
Replacing the camera lens glass on the Motorola Moto G Stylus (2020) is a practical repair that can restore your phone’s camera quality without major cost.
Take your time, follow each step carefully, and you’ll achieve a clean, professional result.
Let us know if you have any questions, and don’t forget to share your experience
Related Guides
