OnePlus Nord N10 5G LCD Screen Replacement Guide | DIY Repair

If the display on your OnePlus Nord N10 5G is cracked, showing lines, not responding to touch, or completely black, replacing the LCD screen assembly can restore the phone’s functionality. Screen damage is one of the most common smartphone issues caused by accidental drops or pressure on the device.

In this beginner-friendly guide, we will explain how to replace the LCD screen display on the OnePlus Nord N10 5G step by step. This repair involves removing several internal components, so patience and careful handling are important.

✅ Protect Your Oneplus Nord N10 5G

• Protector For The Screen https://amzn.to/468xSlq
• Best Rated Case https://amzn.to/468xSlq

---

Repair Overview

---

Reasons for LCD Screen Replacement

You may need to replace the screen if you experience any of the following:

• Cracked or shattered display glass
• Touchscreen not responding
• Screen showing lines or flickering
• Black screen while the phone is still powered on
• Display discoloration or dead pixels
• Screen lifting from the frame

Replacing the display assembly restores both the visual display and touch functionality of the device.

---

Before You Begin

Compatibility and Model Numbers

• Oneplus Nord N10 5G

This repair guide based on OnePlus 8T

Model Numbers | BE2029, BE2025, BE2026, BE2028

---

Tools Required

• Mobile phone heating pad or hairdryer/heat gun
• Plastic pry tool / card pry
• Suction cups
• Phillips #00/#000 screwdrivers
• Torx T3 / T4 Screwdriver (Depends on the region)
• Flathead Screwdriver
• Tweezers (for connectors)
• B7000 glue or double-sided adhesive (for back cover)
• Rubber bands or bonding clips to secure the back cover

Using proper tools reduces the risk of damaging the phone.

How to Find Tools and Parts

• Heating pad – https://amzn.to/3H0tHzJ
• Portable Heat Gun – https://amzn.to/4mszih1
• Clamps https://amzn.to/3GYJT4w
• STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
• Glue | Adhesive https://amzn.to/46exVxe
• Compatible Parts –
  • Battery – https://amzn.to/45YFckS
  • Screen –  https://amzn.to/4p7sEyW
  • Other Parts – https://amzn.to/4m2r6n3
• Silicone Work Repair Mat https://amzn.to/45Emz5l

---

OnePlus Nord N10 5G LCD Screen Replacement – Step-by-Step Guide

Step 1: Remove the Back Cover

Start by removing the back cover from the phone.

Heat the edges of the back cover gently until the adhesive becomes soft.

You can use:

• Heating pad
• Heat gun
• Hairdryer

If using a heating pad, place the phone with the back cover facing down and select the mobile phone heating option until the cycle completes.

---

Step 2: Create an Opening

Attach a suction cup to the back cover and gently pull to create a small opening.

Insert a plastic pry tool or plastic card and slide it around the edges to cut the adhesive.

---

Step 3: Remove the Back Cover

Apply heat around the fingerprint sensor area to soften the glue.

Hold the fingerprint button carefully and lift the back cover away from the phone body.

---

Step 4: Remove the Camera Lens Frame

Remove the four screws securing the camera lens frame.

Lift the frame from the device.

---

Step 5: Remove the SIM Tray

Use a SIM eject tool to remove the SIM tray.

---

Step 6: Remove the Mid-Frame

Remove the 11 screws located on the top and bottom sections.

Using a plastic pry tool, gently separate the mid-frame from the device. Work around the edges to release the plastic clips.

---

Step 7: Disconnect the Battery

Disconnect the battery connector on the right-hand side to prevent electrical damage during the repair.

---

Step 8: Disconnect Antennas and Display Cables

Disconnect the following components from the main board:

• Two antenna connectors
• Primary cable
• LCD display cable

---

Step 9: Remove the Logic Board

Undo the screw securing the logic board.

Carefully lift the logic board using tweezers and remove it from the device.

---

Step 10: Remove the Earpiece

Apply gentle heat to soften the adhesive and remove the earpiece speaker.

---

Step 11: Remove the Power Flex Cable

Apply heat and gently peel off the power button flex cable.

---

Step 12: Remove the Volume Flex Cable

Apply heat to soften the adhesive and remove the volume button flex cable.

---

Step 13: Remove the Speaker Cover

Undo the three screws securing the speaker cover and remove it.

---

Step 14: Remove the Charging Port Board

Disconnect the primary cable and peel the center cable from the body.

Carefully lift and remove the charging board with the headphone jack.

---

Step 15: Remove the Vibrator Motor

Apply heat to loosen the adhesive and remove the vibrator motor.

---

Step 16: Remove the Battery

Loosen the adhesive strips securing the battery.

Pull the adhesive tabs slowly and lift the battery from the device.

---

Step 17: Remove the Main Flex Cable

Move the battery protective tape aside.

Peel the main flex cable from the phone body while removing the adhesive strip from the edge.

---

Step 18: Replace the Screen Assembly

At this stage, only the damaged screen assembly with the frame remains.

There are two types of replacement displays available:

1. Screen with frame – easier installation
2. Screen without frame – requires transferring all components

For beginners, the screen with frame is highly recommended because it simplifies the installation process.

Replacement screens may be:

• Original
• Refurbished
• Used
• Aftermarket

---

Step 19: Transfer Components to the New Frame

Begin installing components into the new screen frame in the following order:

1. Install the power flex cable
2. Install the volume flex cable
3. Install the earpiece speaker
4. Place and secure the logic board and connect the LCD plug
5. Install the vibrator motor

---

Step 20: Install the Charging Port Board

Place and secure the charging board and headphone jack.

Position the antenna cables in the frame and reconnect them to the main board.

---

Step 21: Reinstall the Main Flex Cable

Place and connect the main flex cable at both ends.

Secure the adhesive strip and protective tape.

---

Step 22: Reinstall the Speaker Module

Install the speaker cover and secure it using the three screws.

---

Step 23: Reinstall the Battery

Place the battery back into the phone and secure the adhesive strips.

Reconnect the battery connector.

---

Step 24: Reassemble the Mid-Frame

Place the mid-frame back onto the device and secure it using the 11 screws.

Ensure all clips are properly fastened.

Insert the SIM tray.

---

Step 25: Reinstall the Camera Lens Frame

Place the camera lens frame back onto the phone and secure it with the four screws.

---

Step 26: Test the Device

Before closing the phone completely, power on the device to verify:

• Display works correctly
• Touchscreen responds properly
• Cameras and buttons function normally

---

Step 27: Reattach the Back Cover

Before installing the back cover, check if the adhesive is still strong.

If needed, apply B7000 adhesive or install new double-sided back cover adhesive.

Press the back cover firmly into place.

For better bonding, you can use clamps or rubber bands for a short time while the adhesive sets.

---

Frequently Asked Questions (FAQ)

Q1: Should I buy a screen with frame or without frame?

For beginners, a screen with frame is recommended because it requires fewer steps and reduces the risk of damage.

Q2: How long does this repair take?

The repair usually takes 60 to 90 minutes, depending on experience level.

Q3: Will replacing the screen fix touch problems?

Yes, if the touch digitizer was damaged, replacing the screen assembly will restore touch functionality.

Q4: Is the screen replacement difficult?

Yes. This repair is considered advanced because many internal components must be removed.

Q5: Do I need special adhesive to close the phone?

You can use B7000 glue or pre-cut double-sided adhesive designed for smartphone repairs.

---

Troubleshooting After Screen Replacement

Q1: Screen turns on but touch does not work

Check that the LCD connector is fully seated on the logic board.

Q2: Display flickers or shows lines

The display cable may not be properly connected. Reopen the phone and reconnect the LCD cable.

Q3: Phone does not power on

Verify the battery connector is securely attached and the battery has charge.

Q4: Screen lifts from the frame

Ensure proper adhesive is applied and allow enough time for the glue to cure.

Related Guides

More Oneplus Nord N10 5G Repair Guides

View Oneplus Nord 5G Repair Guides

Check Oneplus 8 Replacement guide