Now Reading: iPad Pro 10.5-inch Battery Replacement Guide | Step-by-Step
-
01
iPad Pro 10.5-inch Battery Replacement Guide | Step-by-Step
Meta Title:
Meta Description: Step-by-step guide to replace the battery on iPad Pro 10.5 (2017). Learn repair difficulty, tools needed, troubleshooting, FAQs, and safe battery installation tips.
Introduction
The iPad Pro 10.5 (2017) is still a powerful and popular tablet, but over time its battery performance can degrade. If your iPad drains quickly, shuts down unexpectedly, or struggles to hold a charge, a battery replacement is often the best solution.
In this guide, we’ll show you how to replace the battery on the iPad Pro 10.5 (2017) safely and correctly. This repair involves removing the display, logic board, and battery, so proper heating and patience are essential. Follow each step carefully to avoid damaging internal components.
Reasons for Battery Replacement
You may need to replace the iPad Pro 10.5 battery if you notice:
✅ Rapid battery drain
✅ iPad shutting down at high battery percentages
✅ Battery not charging properly
✅ Overheating during use or charging
✅ Swollen battery causing screen lift
✅ Poor performance after long-term use
Repair Difficulty
Difficulty Level: ⭐⭐⭐⭐☆ (Hard)
Estimated Time: 60–90 minutes
Repair Type: Battery Replacement
This repair requires full disassembly of the iPad, including removal of the display and logic board. No soldering is required, but strong adhesive and delicate connectors make careful handling essential.
Before You Begin
Compatibility and Model Numbers
This repair guide based on iPad Pro 12.9-inch 2015 Model.
Also Compatible with Both Wifi and Cellular Edition models.
Model Numbers | iPad Pro 12.9-inch 1st Generation, A1584, A1652
Required Tools
- Heating pad / heat gun / hairdryer
- Suction cup
- Plastic card pry tools / opening picks/ Tweezers
- Phillips screwdriver #00 / #000
- Torx T3 Screwdriver
- Adhesive (B7000 or double-sided back cover adhesive)
- Bonding clips or rubber bands (optional but recommended)
Make sure the device is turned off and the SIM tray is removed (For Cellular Version)before starting.
How to Find Tools and Parts
- Heating pad – https://amzn.to/3H0tHzJ
- Portable Heat Gun – https://amzn.to/4mszih1
- Clamps https://amzn.to/3GYJT4w
- STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
- Glue | Adhesive https://amzn.to/46exVxe
- Compatible Parts –
- Battery – https://amzn.to/3V1W1oI
- LCD Screen – https://amzn.to/45NC0Zc
- Other Parts – https://amzn.to/45NC3nQ
- Silicone Work Repair Mat https://amzn.to/45Emz5l
Protect Your iPad
- Tempered Glass For The Screen https://amzn.to/3K8pydS
- Best Cases For Your iPad https://amzn.to/4m4mYCZ
- Missing Keypad for the iPad https://amzn.to/4mPe25W
Step-by-Step iPad Pro 10.5 Battery Replacement
Step 1: Heat the Front Screen
Proper heating is the most critical part of iPad repairs.
- Use a heating pad designed for tablets and mobile devices.
- Heat the front side of the iPad.
- Select the Tablet heating option and allow the cycle to complete.
- Alternatively, use a heat gun with caution.
Step 2: Lift the Screen
- Attach a suction cup to the side of the display.
- Gently lift to create a gap.
- Insert plastic card pry tools and cut the adhesive around the screen.
⚠️ Be gentle—display flex cables are connected to the logic board.
Step 3: Open the Display
- Once separated, slightly slide the screen upward from the bottom.
- Lift the display to about 90 degrees from the top.
Step 4: Disconnect the Display Assembly
- Remove two screws securing the connector shield.
- Take out the shield.
- Disconnect four connector plugs.
- Remove the LCD and touch assembly.
Step 5: Disconnect the Battery
- Remove the screw securing the battery connector.
- Disconnect the battery.
Step 6: Remove the Logic Board Shield
- Undo ten screws.
- Remove the logic board shield.
Step 7: Remove Charging Port Screws
- Undo four screws from the charging port.
Step 8: Disconnect Logic Board Connectors
- Disconnect four connectors from the top end of the logic board.
- Remove two antenna heads from the board.
- Loosen adhesive and disconnect left and right speaker plugs.
Step 9: Heat the Rear Side
- Apply light heat to the rear side of the iPad.
- This softens the adhesive under the logic board and battery.
Step 10: Remove the Logic Board
- Use a card pry tool to gently cut the adhesive beneath the logic board.
- Slightly lift the board.
- Continue cutting adhesive carefully.
- Slowly lift and remove the logic board.
Step 11: Remove the Battery
- Use a pry tool to cut the strong adhesive under the battery.
- This step takes time—be patient.
- Loosen adhesive from both sides while lifting.
Step 12: Install the New Battery
- Always use a high-quality branded or original battery.
- Place adhesive in the battery area.
- Install the new battery into the body.
- Reapply speaker adhesives.
Step 13: Reinstall the Logic Board
- Gently place the logic board back into the body.
- Insert the charging port correctly first.
- Ensure cables are moved aside before seating the board.
Step 14: Reconnect Components
- Secure five connector plugs.
- Connect both speaker plugs and apply adhesive.
- Attach both antenna heads.
Step 15: Reinstall Shields and Screws
- Place the logic board shield and secure it with ten screws.
- Secure the battery connector screw.
- Add four screws to the charging port board.
Step 16: Reinstall the Display
- Keep the screen at a 90-degree angle from the bottom.
- Connect four display connectors.
- Secure the connector shield using two screws.
Step 17: Final Testing & Sealing
- Power on the iPad and test screen and touch functionality.
- Apply adhesive (B7000 or double-sided tape).
- Place the bottom section first, then the top.
- Press the sides and bottom simultaneously.
Ensure the home button sits correctly and clicks properly.
Step 18: Clamp the Screen
- Use screen bonding clips or rubber bands.
- Leave them in place for some time to ensure proper adhesion.
FAQ
Q: How long does an iPad Pro 10.5 battery last?
A: Typically 2–3 years depending on usage and charging habits.
Q: Can I replace the battery without removing the logic board?
A: No. The logic board must be removed to access the battery safely.
Q: Is it safe to use third-party batteries?
A: Use only high-quality branded or original batteries to avoid swelling or performance issues.
Q: Will this repair erase my data?
A: No, battery replacement does not affect stored data.
Troubleshooting (After The Repair)
Q: iPad not powering on after battery replacement.
A: Recheck the battery connector and ensure it’s firmly connected.
Q: Screen not responding after reassembly.
A: Display connectors may be loose. Open the device and reseat them.
Q: Battery draining fast after replacement.
A: Ensure the battery is genuine and calibrate it by fully charging and discharging once.
Q: Screen lifting after repair.
A: Adhesive may not be strong enough. Reapply adhesive and clamp again.
Final Thoughts
Replacing the battery on the iPad Pro 10.5 (2017) is a complex but rewarding repair. With proper heating, patience, and careful handling of components, you can significantly extend the life of your iPad.
Hope you enjoyed this battery repair guide.
If you have any questions, feel free to comment. Please like, share, and subscribe to Geardo for more repair guides.
Related Guides
