Now Reading: OnePlus 8T LCD Flex Cable Replacement Guide | DIY Repair
-
01
OnePlus 8T LCD Flex Cable Replacement Guide | DIY Repair
If your OnePlus 8T is experiencing touch issues, display flickering, or a completely unresponsive screen, the LCD flex cable may be faulty or damaged. Replacing the LCD flex cable restores full display functionality and ensures proper communication between the logic board and the screen. This guide will walk you through the entire process—from opening the phone to reassembly—so you can safely replace your LCD flex cable at home.
Repair Overview
Device Type: Smartphone
Repair Type: Internal Battery Replacement
Repair Difficulty : ★★★★★☆☆☆☆☆ (5/10 – Moderate)
Estimated Time: 60–90 minutes
Reasons for OnePlus 8T LCD Flex Replacement
- Touch screen not responding
- Flickering or distorted display
- Lines or black areas on the screen
- Intermittent screen functionality
- Display not detected after impact or drop
- Physical damage to the flex cable or connector
Replacing the LCD flex cable is a precise repair that can restore full display performance without needing a full screen replacement in some cases.
Before You Begin
Compatibility and Model Numbers
- Oneplus 8T
- Oneplus 8T+ 5G
This repair guide based on OnePlus 8T
Model Numbers | KB2001, KB2000, KB2003, KB2005, KB2007
Tools Required
- Mobile phone heating pad or hairdryer/heat gun
- Plastic pry tool / card pry
- Suction cups
- Phillips #00/#000 screwdrivers
- Torx T3 / T4 Screwdriver
- Flathead Screwdriver
- Tweezers (for connectors)
- B7000 glue or double-sided adhesive (for back cover)
- Rubber bands or bonding clips to secure the back cover
Using proper tools reduces the risk of damaging the phone.
How to Find Tools and Parts
- Heating pad – https://amzn.to/3H0tHzJ
- Portable Heat Gun – https://amzn.to/4mszih1
- Clamps https://amzn.to/3GYJT4w
- STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
- Glue | Adhesive https://amzn.to/46exVxe
- Compatible Parts –
- Battery – https://amzn.to/3IgZ75c
- Screen – https://amzn.to/46iYhNy
- Other Parts – https://amzn.to/47Hh2N3
- Silicone Work Repair Mat https://amzn.to/45Emz5l
Protect Your Oneplus 8T
Protector For The Screen https://amzn.to/4nXZi55
Best Rated Case https://amzn.to/46acCf2
Step-by-Step OnePlus 8T LCD Flex Replacement Guide
Step 1 – Prepare Tools & Power Off the Device
Before starting, make sure you have all necessary repair tools, including pry tools, screwdrivers, suction cups, and adhesive. Proper tools prevent damage and make the repair safer and easier.
Turn off your device completely and remove the SIM tray.
Step 2 – Remove the Back Cover
- Heat the edges of the back cover using a heating pad, heat gun, or hair dryer until the adhesive softens.
- Use a suction cup to lift the cover slightly.
- Slide a plastic card or pry tool around the edges to separate all adhesive and remove the back cover carefully.
Step 3 – Remove the Logic Board Frame
- Unscrew all screws securing the logic board frame.
- Use a pry tool to gently lift the frame, exposing the secondary board and internal components.
Step 4 – Remove the Secondary Board Cover
- Unscrew and remove the secondary board protective cover.
- This exposes the main flex, charging port, and LCD flex connections.
Step 5 – Remove the Main Flex Cable
- Disconnect the main flex cable connecting the logic board and secondary board.
- Lift the old flex carefully, avoiding damage to connectors.
Step 6 – Remove the Charging Port and Battery
- Unscrew and lift out the charging port flex cable.
- Disconnect and remove the battery carefully to access the LCD flex cable underneath.
Step 7 – Remove the Broken LCD Flex Cable
- Gently disconnect the old LCD flex cable from the logic board.
- Carefully lift it out of the housing without bending or tearing it.
Step 8 – Install the New LCD Flex Cable
- Place the new LCD flex cable in the same position as the old one.
- Connect it securely to the logic board.
- Ensure the cable sits flat with no kinks or folds.
Step 9 – Reinstall the Battery and Charging Port
- Place the battery back in its housing and reconnect it.
- Reinstall the charging port and secure it with screws.
- Verify proper alignment with the flex connectors.
Step 10 – Reconnect the Main Flex Cable
- Reconnect the main flex cable to the logic board and secondary board.
- Ensure all connectors are fully seated and locked.
Step 11 – Replace the Secondary Board Cover
- Place the secondary board protective cover back over the components.
- Secure it with screws, making sure the loudspeaker buzzer and all other elements are aligned properly.
Step 12 – Reassemble the Logic Board Frame
- Carefully place the logic board frame back in position.
- Tighten all screws and confirm all connectors are aligned.
Step 13 – Reinstall the Back Cover
- Ensure there is enough adhesive around the edges.
- Use B7000 glue or fresh double-sided adhesive if needed.
- Press the back cover evenly onto the device.
- Apply binding clips or rubber bands to hold the cover while the adhesive cures (30–60 minutes).
Finally, reinsert the SIM tray and power on the device to test the new LCD flex cable.
Frequently Asked Questions (FAQ)
Q1: Will replacing the LCD flex fix a completely black screen?
Yes, if the screen issue is caused by a damaged flex cable rather than a broken display.
Q2: Can I replace the LCD flex without removing the battery?
No. Removing the battery ensures safe access and prevents short circuits.
Q3: How do I know if the flex cable is the problem?
Symptoms include touch not responding, flickering, distorted lines, or intermittent display issues after a drop or impact.
Q4: Do I need special adhesive for the back cover?
Yes. Use B7000 glue or double-sided adhesive to secure the back cover.
Q5: How long should I leave the binding clips on the back cover?
30–60 minutes for a proper adhesive cure.
Troubleshooting After LCD Flex Replacement
Q1: Screen still not responding
Check that the LCD flex cable is seated properly and that all connectors are locked.
Q2: Display flickering or showing lines
Ensure the flex cable is flat, not bent, and that the connectors are clean and undamaged.
Q3: Back cover lifting
Reapply adhesive and leave binding clips on longer.
Q4: Touch screen intermittently works
Verify that the main flex and LCD flex are fully connected.
Q5: Device not powering on after reassembly
Ensure the battery connector is securely connected to the logic board.
Replacing the LCD flex cable on the OnePlus 8T is a moderate-level repair that can restore proper display functionality. With patience, proper tools, and careful handling, you can complete this repair successfully at home.
If you found this guide helpful, feel free to explore more repair tutorials to keep your devices running like new.
Related Guides
