OnePlus Nord N10 5G Charging Port Replacement Guide | DIY Repair

If your OnePlus Nord N10 5G is not charging properly, the charging cable feels loose, or your phone only charges at certain angles, the charging port board may be damaged. This small but important component manages charging and often connects to the microphone and antenna components as well.

In this beginner-friendly repair guide, we will walk you through how to replace the charging port board on the OnePlus Nord N10 5G step by step. With the proper tools and careful handling, this repair can be completed at home.

Replacing the charging port board can restore proper charging functionality and extend the lifespan of your device.

✅ Protect Your Oneplus Nord N10 5G

• Protector For The Screen https://amzn.to/468xSlq
• Best Rated Case https://amzn.to/468xSlq

---

Repair Overview

---

Reasons for Charging Port Board Replacement

You may need to replace the charging port board if you experience the following problems:

• Phone not charging when plugged in
• Charging cable feels loose in the port
• Device charges only when the cable is positioned in a certain way
• Slow or inconsistent charging
• Charging port physically damaged or corroded
• Microphone not working (sometimes connected to the same board)

Replacing the charging port board can fix these issues and restore stable charging performance.

---

Before You Begin

Compatibility and Model Numbers

• Oneplus Nord N10 5G

This repair guide based on OnePlus 8T

Model Numbers | BE2029, BE2025, BE2026, BE2028

---

Tools Required

• Mobile phone heating pad or hairdryer/heat gun
• Plastic pry tool / card pry
• Suction cups
• Phillips #00/#000 screwdrivers
• Torx T3 / T4 Screwdriver (Depends on the region)
• Flathead Screwdriver
• Tweezers (for connectors)
• B7000 glue or double-sided adhesive (for back cover)
• Rubber bands or bonding clips to secure the back cover

Using proper tools reduces the risk of damaging the phone.

How to Find Tools and Parts

• Heating pad – https://amzn.to/3H0tHzJ
• Portable Heat Gun – https://amzn.to/4mszih1
• Clamps https://amzn.to/3GYJT4w
• STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
• Glue | Adhesive https://amzn.to/46exVxe
• Compatible Parts –
  • Battery – https://amzn.to/45YFckS
  • Screen –  https://amzn.to/4p7sEyW
  • Other Parts – https://amzn.to/4m2r6n3
• Silicone Work Repair Mat https://amzn.to/45Emz5l

---

OnePlus Nord N10 5G Charging Port Board Replacement – Step-by-Step Guide

Step 1: Remove the Back Cover

Begin by removing the back cover from the phone.

The back cover is secured with adhesive, so gently heat around the edges of the back cover until the glue becomes soft.

You can use a heating pad, heat gun, or hairdryer.

If using a heating pad, place the phone with the back cover facing down and select the mobile phone heating option, allowing it to complete the heating cycle.

---

Step 2: Create an Opening

Attach a suction cup to the back cover and gently lift it to create a small gap.

Insert a plastic pry tool or plastic card into the gap and carefully slide it around the edges to cut the adhesive.

Take your time to avoid damaging internal components.

---

Step 3: Remove the Back Cover

Apply gentle heat to the fingerprint sensor area to soften the glue.

Hold the fingerprint button and carefully pull the back cover away from the phone body.

---

Step 4: Remove the Camera Lens Frame

Using a Phillips screwdriver, remove the four screws securing the camera lens frame.

Lift the frame out of the phone.

---

Step 5: Remove the SIM Tray

Use a SIM eject tool to remove the SIM tray from the device.

---

Step 6: Remove the Midframe

Remove the 11 screws located at the top and bottom of the phone.

Using a plastic pry tool, gently separate the mid-frame from the phone body.

Work around the edges carefully to release the plastic clips.

---

Step 7: Disconnect the Battery

Locate the battery connector on the right-hand side and disconnect it using a plastic pry tool.

This prevents accidental electrical damage during the repair.

---

Step 8: Remove the Speaker Cover

Undo the three screws securing the speaker cover.

Lift and remove the speaker cover from the device.

---

Step 9: Disconnect Board Cables

Disconnect the following components from the charging port board:

• Main flex cable
• Two antenna connectors

Use tweezers or a plastic pry tool for safe removal.

---

Step 10: Remove the Charging Port Board

Carefully lift and remove the damaged charging port board from the phone body.

Handle the board gently to avoid damaging nearby components.

---

Step 11: Install the New Charging Port Board

Place the new charging port board into the correct position inside the phone.

Ensure it sits properly in the designated slot.

---

Step 12: Reconnect the Cables

Reconnect the following components to the new board:

• Main flex cable
• Two antenna connectors

Make sure all connectors are securely attached.

---

Step 13: Reinstall the Speaker Cover

Place the speaker cover back into position and secure it using the three screws removed earlier.

---

Step 14: Reconnect the Battery

Reconnect the battery connector to the motherboard.

---

Step 15: Reinstall the Midframe

Place the mid-frame back onto the phone body.

Ensure all clips snap into place before reinstalling the 11 screws.

Insert the SIM tray back into the device.

---

Step 16: Reinstall the Camera Lens Frame

Place the camera lens frame back onto the device and secure it with the four screws.

---

Step 17: Reattach the Back Cover

Before reinstalling the back cover, check if the adhesive is still strong.

If necessary, apply B7000 glue or a new double-sided back cover adhesive.

Align the back cover carefully and press firmly around the edges.

---

Frequently Asked Questions (FAQ)

Q1: Can I replace the OnePlus Nord N10 5G charging port myself?

Yes. With the right tools and patience, beginners can replace the charging port board by following this guide.

Q2: How long does this repair take?

Most users can complete the repair within 40 to 60 minutes.

Q3: Will replacing the charging port fix slow charging?

Yes, if the issue is caused by a damaged or worn charging port board, replacing it will restore proper charging performance.

Q4: Do I need soldering for this repair?

No. The charging port board in the OnePlus Nord N10 5G is modular and connects using cables, so soldering is not required.

Q5: What adhesive should I use when closing the phone?

You can use B7000 adhesive or pre-cut double-sided adhesive designed for smartphone back covers.

---

Troubleshooting After Charging Port Replacement

Q1: Phone still does not charge

Check that the main flex cable and battery connector are properly connected.

Also test the phone with a different charging cable and charger.

Q2: Charging works but data transfer does not

Make sure the main flex cable is fully seated on the charging port board.

Q3: No sound from the bottom speaker

Ensure the speaker cover is installed correctly and secured with all screws.

Q4: Back cover does not stick properly

Clean the edges of old adhesive and apply new adhesive or B7000 glue.

Related Guides

More Oneplus Nord N10 5G Repair Guides

View Oneplus Nord 5G Repair Guides

Check Oneplus 8 Battery Replacement guide