Now Reading: Samsung Galaxy A11 Camera Lens Glass Replacement Guide | Back Cover
-
01
Samsung Galaxy A11 Camera Lens Glass Replacement Guide | Back Cover
A scratched, cracked, or broken camera lens glass can seriously affect photo quality even when the camera itself is perfectly functional. Dust entry, blurry images, light glare, or focusing problems are common signs that the outer lens glass has been damaged. Fortunately, replacing the camera lens glass on the Samsung Galaxy A11 is a quick and affordable repair that restores clear photography without replacing expensive camera modules.
This DIY guide explains how to safely replace the rear camera lens glass using proper tools and careful handling techniques.
Protect Your Galaxy A11
- Protector For The Screen https://amzn.to/4gcQxBg
- Best Rated Case https://amzn.to/45Tjoai
- Latest Samsung Phones are in Clearence https://amzn.to/4b9xBSM
Repair Difficulty ⭐⭐☆☆☆ (Easy to Moderate)
Estimated Repair Time: 15 — 25 Minutes
Device Type: Smartphone
Repair Type: Rear Camera Lens Glass Replacement
Reasons to Replace the Samsung Galaxy A11 Camera Lens Glass
You may need lens glass replacement if you notice:
- Cracked or shattered camera lens cover
- Blurry or foggy photos
- Dust visible inside the camera area
- Light glare or reflection in images
- Moisture entering through damaged lens glass
- Scratches affecting image clarity
Replacing only the lens glass protects internal cameras and restores photo quality at a much lower cost.
Before You Begin
Compatibility and Model Numbers
- Samsung Galaxy A11
- Samsung Galaxy M11
This repair guide based on Samsung Galaxy A11 Model.
Model Numbers | SM-A115F/DS, SM-A115F, SM-A115M, SM-A115M/DS, SM-A115U, SM-A115A, SM-A115AZ, SM-A115U1, SM-A115W, SM-A115AP, SM-S115DL, SM-M115F, SM-M115F/DSN, SM-M115M, SM-M115M/DS
Tools Required
- Mobile phone heating pad or hairdryer/heat gun
- Plastic pry tool / card pry
- Suction cups
- Phillips #00/#000 screwdrivers
- Flat Screwdriver (Handy For Connectors)
- Tweezers (for connectors)
- B7000 glue or double-sided adhesive (for back cover)
- Rubber bands or bonding clips to secure the back cover
Using proper tools reduces the risk of damaging the phone.
How to Find Tools and Parts
- Heating pad – https://amzn.to/3H0tHzJ
- Portable Heat Gun – https://amzn.to/4mszih1
- Clamps https://amzn.to/3GYJT4w
- STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
- Glue | Adhesive https://amzn.to/46exVxe
- Compatible Parts –
- Battery – https://amzn.to/41FdUgG
- Screen – https://amzn.to/4mSDJT6
- Other Parts – https://amzn.to/4gkS88c
- Silicone Work Repair Mat https://amzn.to/45Emz5l
Samsung Galaxy A11 Camera Lens Glass Replacement — Step-by-Step Guide
Step 1 — Power Off and Remove SIM Tray
Turn off the phone completely before starting the repair.
Remove the SIM tray using a SIM ejector tool.
Step 2 — Remove the Back Cover
Create a small opening gap near the SIM slot or charging port using a plastic picker or card pry tool.
Insert the pry card carefully between the frame and the back cover.
Move slowly around the edges to release the plastic clips securing the back panel.
⚠️ Lift gently because the fingerprint sensor cable is attached to the back cover.
Step 3 — Remove Fingerprint Sensor From Back Cover
Apply gentle heat to soften the adhesive holding the fingerprint button.
Carefully push and remove the fingerprint switch from the back cover.
Once removed safely, separate the back cover completely from the phone body.
Step 4 — Remove the Broken Camera Lens Glass
Apply moderate heat to the camera lens area on the back cover to soften adhesive.
From the rear side, gently push the damaged lens glass outward.
Remove broken glass pieces carefully.
⚠️ Clean any remaining adhesive or dust before installing the new lens.
Step 5 — Install New Camera Lens Glass
Place the replacement camera lens glass into position.
If adhesive is pre-installed, press gently to secure it.
If required, apply a small amount of glue around the edges.
Ensure proper alignment with the camera openings.
Step 6 — Prepare Fingerprint Holder Area
If needed, apply a small amount of adhesive around the fingerprint holder area on the back cover.
Make sure adhesive does not block the sensor opening.
Step 7 — Reinstall Fingerprint Sensor
Place the fingerprint button back into position.
Press gently until it sits securely.
Step 8 — Reassemble the Phone
Align the back cover with the frame carefully.
Press around the edges to snap the clips securely into place.
Insert the SIM tray.
Power on the device and test the camera before regular use.
Frequently Asked Questions (FAQ)
Does replacing the camera lens glass affect the camera module?
No. The lens glass is separate from the camera modules. Replacement does not affect stored data or camera software.
Can I use glue instead of adhesive?
Yes. A small amount of phone-safe adhesive can be used if the replacement lens does not include adhesive backing.
Do I need heat during this repair?
Yes. Heat softens adhesive and prevents damage when removing the broken lens.
Why are my photos still blurry after replacement?
Check whether dust or fingerprints touched the camera lenses during installation.
Can beginners perform this repair?
Yes. This is one of the easier smartphone repairs when done carefully.
Troubleshooting After Camera Lens Replacement
Dust visible inside the camera
Remove the back cover again and clean the lens area using compressed air or microfiber cloth.
Lens glass not sitting flat
Remove excess adhesive and reinstall the lens evenly.
Fingerprint sensor not working
Check whether the fingerprint button was properly seated during installation.
Back cover not snapping closed
Inspect cable placement and confirm nothing is blocking the clips.
Related Guides
