iPhone XS Screen Replacement Guide | LCD & Touch DIY Repair

Hi everyone, welcome back to Geardo. Today we will show you how to replace the LCD & Touch screen assembly on the iPhone XS mobile phone.

If your screen is cracked, unresponsive, or displaying lines or black spots, replacing the display assembly is the best solution. This guide is designed for beginners and will help you safely complete the repair step by step.

Before starting, make sure you have the right tools to proceed with the repair, which you can find in the description.

---

Repair Overview

• Device Type: Smartphone
• Device Model: iPhone XS
• Repair Type: LCD & Touch Screen Replacement

Repair Difficulty

⭐⭐⭐☆☆ (3/5 – Moderate)

Estimated Time

30–45 minutes

---

Reasons for Screen Replacement

• Cracked or shattered screen
• Touch not responding
• Display flickering or showing lines
• Black spots or dead pixels
• Screen not turning on

---

Before You Begin

Compatibility and Model Numbers

• iPhone XS

This repair guide based on iPhone XS Model.

Model Numbers | A2097, A1920, A2100, A2098

Tools Required

• Heating pad / heat gun / hairdryer
• Suction cup
• Plastic card pry tools / opening picks
• Phillips PH000 screwdriver
• Pentalobe P2 Screwdriver (for bottom screws)
• Tri-Point Y000 Screwdriver
• Adhesive (B7000 or double-sided frame adhesive)
• Bonding clips or rubber bands (optional but recommended)

Using proper tools reduces the risk of damaging the phone.

How to Find Tools and Parts

• Heating pad – https://amzn.to/3H0tHzJ
• Portable Heat Gun – https://amzn.to/4mszih1
• Clamps https://amzn.to/3GYJT4w
• STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
• Glue | Adhesive https://amzn.to/46exVxe
• Compatible Parts –
  • Battery – https://amzn.to/4fI15YG
  • Screen – https://amzn.to/3VIu2KN
  • Other Parts – https://amzn.to/4n2vPq4
• Silicone Work Repair Mat https://amzn.to/45Emz5l

---

 Protect Your iPhone X

2 in 1 Protection for Your iPhone XS https://amzn.to/46apLVC

---

Step-by-Step iPhone XS Screen Replacement Guide

Step 1: Power Off & Remove Screws

Turn off the phone.
Remove the SIM tray.
Undo the two bottom screws using a Pentalobe screwdriver.

---

Step 2: Open the Display

Use a suction cup to lift the screen.

If needed:

• Use a plastic pry tool or triangle picker
• Carefully separate the adhesive around the frame

---

Step 3: Open the Screen

Lift the display gently like opening a book.

Remove five screws and take off the protective shield.

Disconnect:

• Touch connector
• LCD connector
• Earpiece assembly connector

---

Step 4: Transfer Earpiece Assembly

On the broken screen:

• Remove three screws
• Take out the earpiece assembly and bracket

---

Step 5: Install Components on New Screen

On the new replacement screen:

• Place the bracket
• Install the earpiece assembly
• Secure it with three screws

💡 Tip: Before installing the earpiece, connect the new screen temporarily and test it.

---

Step 6: Apply Adhesive Seal

Apply the pre-cut water seal adhesive around the frame.

⚠️ Note: This does not fully restore waterproofing.

---

Step 7: Reconnect Display

Reconnect:

• LCD connector
• Touch connector
• Earpiece assembly connector

Ensure all connections are secure.

Reinstall the shield using five screws.

---

Step 8: Close the Device

Press the display into place:

• Start from the top
• Then press sides
• Then bottom

Apply even pressure along the frame.

---

Step 9: Final Assembly & Test

Turn on the phone and test the screen.

Once verified:

• Insert SIM tray
• Tighten the two bottom screws

---

FAQs

1. Can I replace the iPhone XS screen myself?

Yes, this repair is beginner-friendly if you follow the steps carefully.

2. Do I need to transfer the earpiece assembly?

Yes, the original earpiece assembly must be transferred for proper functionality.

3. Will Face ID work after screen replacement?

Yes, as long as the original earpiece/Face ID module is not damaged.

4. Should I test the new screen before sealing?

Yes, always test the display before final assembly.

5. Does replacing the screen affect waterproofing?

Yes, the original seal is broken. The new adhesive offers limited protection.

---

Troubleshooting (After The Repair)

1. Screen not turning on

• Check LCD connector
• Ensure battery is connected

2. Touch not working

• Reconnect touch connector
• Ensure no debris is blocking contacts

3. Face ID not working

• Check earpiece assembly connection
• Ensure module is not damaged

4. Screen lifting or not fitting properly

• Check adhesive placement
• Ensure cables are not trapped

---

5. Display flickering

• Ensure connectors are fully secured
• Try reconnecting display cables

---

Final Thoughts

That’s it! You’ve successfully replaced the LCD & touch screen on your iPhone XS.

This repair can make your device feel like new again and is a great way to save money. Just take your time and follow each step carefully.

Hope you enjoyed the repair guide.
Let us know if you have any queries—please like, share, and comment on our videos.

And don’t forget to hit the subscribe button!

Related Guides

Check iPhone XS Repair Guides

View iPhone XR Repair Guides