Motorola Moto G9 Play 2020 Back Cover Replacement Guide | Camera Lens Glass Repair

Hi everyone, Welcome back to geardo.

If your Motorola Moto G9 Play has a cracked camera lens glass or a damaged back cover, it can affect both the appearance and camera performance of your device. Scratched or broken lens glass can lead to blurry photos, dust entering the camera module, and long-term internal damage.

In this guide, we will walk you through a complete step-by-step process to replace the camera lens glass and back cover safely. This is a beginner-friendly repair, but it requires careful handling, especially when applying heat and removing adhesive components.

Make sure you have all the required tools ready before starting.

---

Repair Overview

• Device Type: Smartphone
• Repair Type: Camera Lens Glass & Back Cover Replacement
• Repair Difficulty: ⭐⭐⭐⭐☆
• Estimated Time: 40–60 minutes

---

Reasons for This Repair

• Cracked or scratched camera lens glass
• Blurry or unclear photos
• Dust or moisture inside camera lens
• Broken or damaged back cover
• Loose or lifted rear panel

Check The Latest Motorola Phones are in Clearance “up to 60% off” – https://amzn.to/480ho0w

Before You Begin

Compatibility and Model Numbers

• Motorola Moto G9 Play (2020)

This repair guide based on Motorola Moto G9 Play

Model Numbers | XT2083, XT2083-1, XT2083-3

---

Tools Required

• Mobile phone heating pad or hairdryer/heat gun
• Plastic pry tool / card pry
• Suction cups
• Phillips #00/#000 screwdrivers
• Torx T3 / T4 / T5 Screwdriver (Depends on the version)
• Flathead Screwdriver
• Tweezers (for connectors)
• B7000 glue or double-sided adhesive (for back cover)
• Rubber bands or bonding clips to secure the back cover

Using proper tools reduces the risk of damaging the phone.

How to Find Tools and Parts

• Heating pad – https://amzn.to/3H0tHzJ
• Portable Heat Gun – https://amzn.to/4mszih1
• Clamps https://amzn.to/3GYJT4w
• STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
• Glue | Adhesive https://amzn.to/46exVxe
• Compatible Parts –
  • Battery – https://amzn.to/480hSnm
  • Screen – https://amzn.to/4co8ueB
  • Other Parts – https://amzn.to/4stYExB
• Silicone Work Repair Mat https://amzn.to/45Emz5l

---

Step-by-Step Replacement Guide

Step 1: Power Off and Remove SIM Tray

Turn off the phone and remove the SIM tray.

---

Step 2: Apply Heat

Apply gentle heat around the camera lens and fingerprint sensor area to soften the adhesive.

---

Step 3: Remove Back Cover

Create a gap near the SIM slot or charging port using a pry tool. Insert a plastic card and carefully move around the edges to release the clips.

---

Step 4: Disconnect Fingerprint Sensor

While lifting the back cover, hold the fingerprint sensor and gently detach it.

---

Step 5: Remove Adhesive Strips

Peel off the adhesive strips attached to the frame.

---

Step 6: Remove Fingerprint Sensor

Apply slight heat and gently lift the fingerprint button.

---

Step 7: Remove Midframe

Unscrew the nine screws and remove the board frame.

---

Step 8: Disconnect Battery

Lift the adhesive and disconnect the battery connector.

---

Step 9: Remove Camera Lens Glass

Apply heat to the camera lens glass using a heat gun.
Then apply slight pressure from the inside/right side to push out the broken lens.

---

Step 10: Install New Camera Lens Glass

Place the new camera lens glass with adhesive and align it properly on the frame.

---

Step 11: Reconnect Battery

Reconnect the battery connector and secure the adhesive.

---

Step 12: Reinstall Fingerprint Sensor

Place and secure the fingerprint button.

---

Step 13: Reassemble Midframe

Position the board frame and tighten all nine screws.

---

Step 14: Apply Adhesive

Place adhesive strips along the frame.

---

Step 15: Reattach Back Cover

Snap the back cover into place and press along the edges to secure the clips.

---

Step 16: Insert SIM Tray

Insert the SIM tray back into the device.

---

Frequently Asked Questions (FAQ)

Do I need to replace the back cover if only the lens is broken?

No, you can replace only the camera lens glass if the back cover is still in good condition.

Is it safe to remove the camera lens with heat?

Yes, but use controlled heat to avoid damaging nearby components.

Can dust enter the camera if the lens is cracked?

Yes, and it can affect image quality over time.

Should I use glue or adhesive for the new lens?

It is recommended to use pre-cut adhesive designed for camera lens glass.

Is this repair suitable for beginners?

It is slightly advanced but manageable with patience and proper tools.

---

Troubleshooting

Camera is blurry after replacement

Check if the lens glass is clean and properly aligned.

Fingerprint sensor not working

Ensure the connector is securely attached and not damaged.

Back cover not fitting properly

Make sure adhesive is correctly placed and no cables are blocking the fit.

Camera lens not sticking properly

Use proper adhesive and apply slight pressure for a secure fit.

Phone not turning on

Check the battery connection and ensure it is properly reconnected.

---

Final Notes

This repair requires careful handling, especially when working with heat and small components. Take your time and avoid using excessive force.

If done correctly, replacing the camera lens glass and back cover will restore both the look and functionality of your phone.

If you have any questions, feel free to leave a comment or reach out.

Related Guides

Other Moto G9 Play 2020 Repair Guides

Check Moto One Ace Repair Guides