POCO X3 NFC Battery Replacement Guide | POCO X3 PRO / Poco X3

If your Xiaomi Poco X3, Poco X3 NFC, or Poco X3 Pro is draining battery quickly, shutting down unexpectedly, or overheating during charging, a battery replacement is often the best fix.

This DIY guide is compatible with all three models because they share a very similar internal layout and battery replacement process. Follow this step-by-step tutorial to safely replace the battery and restore normal battery life at home.

---

Repair Overview

• Compatible Models: Xiaomi Poco X3, Poco X3 NFC, Poco X3 Pro
• Repair Type: Battery Replacement
• Repair Difficulty: ⚠️⚠️⚠️ Medium
• Time Required: 30–45 minutes
• Risk Level: Moderate

---

Reasons to Replace the Poco X3 / X3 NFC / X3 Pro Battery

• Battery drains unusually fast
• Phone shuts down suddenly
• Device overheats while charging
• Swollen battery or back cover lifting
• Charging is slow or unstable

---

Before You Begin

Compatibility and Model Numbers

• POCO X3 NFC
• POCO X3
• POCO X3 Pro

Model Numbers : MZB07Z0IN, MZB07Z1IN, MZB07Z2IN, MZB07Z3IN, MZB07Z4IN, MZB9965IN, M2007J20CI, M2007J20CG, M2007J20CT, M2102J20SG, M2102J20SI

Tools Required

• Mobile phone heating pad or hairdryer/heat gun
• Plastic pry tool / card pry
• Suction cups
• Phillips #00/#000 screwdrivers
• Tweezers (for connectors)
• B7000 glue or double-sided adhesive (for back cover)
• Rubber bands or bonding clips to secure the back cover

How to Find Tools and Parts

• Heating pad – https://amzn.to/3H0tHzJ
• Portable Heat Gun – https://amzn.to/4mszih1
• Clamps https://amzn.to/3GYJT4w
• STREBITO 142 Piece Repair Tool Kit https://amzn.to/3UO1jUx
• Glue | Adhesive https://amzn.to/46exVxe
• Compatible Parts –
  • Battery – https://amzn.to/3HR26Bi
  • Screen – https://amzn.to/4mZPXsI
  • Other Parts – https://amzn.to/3HR26Bi
• Silicone Work Repair Mat https://amzn.to/45Emz5l

---

Protect Your Poco X3 Series

• Protector For The Screen https://amzn.to/4gdWWw9
• Best Rated Case https://amzn.to/4fPcV3e

---

Step-by-Step Battery Replacement Guide

Step 1: Remove the SIM Tray

Power off the phone completely. Use a SIM eject tool to remove the SIM tray and keep it aside safely.

---

Step 2: Heat and Remove the Back Cover

Gently heat around the edges of the back cover to soften the adhesive.

• Place the phone back-cover-side down on a heating pad and select the mobile heating option
• Alternatively, use a heat gun or hairdryer

Create an opening using a suction cup and slide a plastic pry tool around the edges to cut the adhesive. Carefully remove the back cover.

---

Step 3: Remove the Board Frame

Undo 11 Phillips screws securing the board frame. Lift and remove it carefully.

---

Step 4: Disconnect the Battery

Locate the battery connector on the left-hand side and disconnect it first to avoid electrical damage.

---

Step 5: Disconnect Other Connectors

Disconnect the fingerprint sensor connector and the top end of the main ribbon flex cable using a plastic tool.

---

Step 6: Remove the Old Battery

Loosen the adhesive on both sides of the battery. Pull gently using the battery tab and lift the battery out slowly.
⚠️ Do not bend or puncture the battery.

---

Step 7: Install the New Battery

Place the new battery into the housing and secure it with adhesive. Make sure it sits flat and aligned.

---

Step 8: Reconnect All Connectors

Reconnect the fingerprint sensor, main flex cable, and battery connector. Double-check that everything is properly seated.

---

Step 9: Reinstall the Board Frame

Place the board frame back in position and secure it with 11 screws. Reinsert the SIM tray.

---

Step 10: Seal the Back Cover

Apply fresh adhesive or B7000 glue to the back cover. Press it firmly into place and use binding clips or rubber bands to hold it tight for several minutes.

---

Frequently Asked Questions (FAQ)

Q: Are these steps the same for Poco X3 Pro and Poco X3 NFC?
A: Yes. The internal layout and battery replacement procedure are nearly identical across all three models.

Q: Will replacing the battery erase my data?
A: No, but backing up your data before repair is always recommended.

Q: How long does a replacement battery last?
A: A good-quality battery typically lasts 1–2 years, depending on usage habits.

---

Troubleshooting (After The Repair)

Q: Phone doesn’t turn on after battery replacement
A: Check the battery connector and make sure it’s fully connected.

Q: Fingerprint sensor not working
A: The fingerprint flex cable may be loose—reseat the connector carefully.

Q: Back cover not sticking properly
A: Clean off old adhesive and apply fresh glue or a new adhesive seal.

---

Final Notes

This Xiaomi Poco X3 series battery replacement guide is designed to help you safely complete the repair at home. Take your time, avoid force, and double-check all connectors before sealing the phone.

Related Guide

View More Poco X3 Series Repair Guides