Google Pixel 5 Rear Camera Replacement

A faulty rear camera can make it impossible to take photos or videos properly with your Google Pixel 5. If the rear camera unit has stopped working, replacing the camera module can restore the phone’s main camera function.

This Google Pixel 5 rear camera replacement guide covers the complete procedure shown in the repair instructions, including removing the display, accessing the camera connectors, replacing the rear camera unit, testing the repair, and reinstalling the screen.

Repair Information

Repair Information	Details
Device	Google Pixel 5
Repair Type	Rear Camera Replacement
Repair Difficulty	★★★☆☆
Estimated Time	Approximately 1 hour

Reasons for the Repair

You may need to replace the Google Pixel 5 rear camera if you experience:

• The rear camera is not working
• The main camera no longer operates correctly
• The rear camera unit has failed
• The phone cannot properly use its rear camera

Important: Take care when opening the phone and working around the display, camera connectors, and internal components. Avoid applying unnecessary force during disassembly.

---

Before You Begin

Compatibility and Model Numbers

This repair guide based on Google Pixel 5

Model Numbers | GD1YQ, GTT9Q, G5NZ6

Tools Required

• Mobile phone heating pad or hairdryer/heat gun
• Plastic pry tool / card pry
• Suction cups
• Torx T3 screwdriver
• Torx T4 screwdriver
• Torx T5 screwdriver
• Tweezers (for connectors)
• B7000 glue or double-sided adhesive (for back cover)
• Rubber bands or bonding clips to secure the back cover

How to Find Tools and Parts

• Heat Mat / Heating Pad – https://amzn.to/3H0tHzJ
• Best Portable Heat Gun – https://amzn.to/4cZYnhL
• Clamps – https://amzn.to/3GYJT4w
• STREBITO 142 Piece Repair Tool Kit – https://amzn.to/3UO1jUx
• Stronger Suction Cup – https://amzn.to/3UVb6YR
• Silicone Work Repair Mat – https://amzn.to/4euW6fs
• Must Have Glue | Adhesive – https://amzn.to/4uxhKog
• Compatible Parts –
  • Battery – https://amzn.to/3JEaxAO
  • Screen – https://amzn.to/4oiq0p7
  • Other Parts – https://amzn.to/4hCRy6a

Step-by-Step Repair

Step 1: Heat and Remove the LCD Screen

Begin by gently heating around the edges of the Google Pixel 5 display to soften the adhesive holding the screen to the phone body.

A heating pad is used in this repair. Place the phone with the front screen facing the heating pad, select the mobile phone heating option, and allow the heating cycle to complete. A heat gun or hairdryer can also be used as an alternative.

Once the adhesive has softened, use a suction cup to lift the display slightly. Insert a plastic card pry tool into the opening and carefully work around the screen to cut through the adhesive.

Be particularly careful around the left-hand side of the display, where the flex connector cable is located. Use the edge of the plastic pry tool and avoid pushing it too far into the phone.

Gradually lift the screen from the right side toward the left and leave it open like a book.

---

Step 2: Disconnect and Remove the Display

Use a tweezer to remove the LCD connector bracket.

Next, disconnect the LCD connector plug from the board.

Once the connector has been disconnected, you can completely separate the display from the phone body.

Clean the edges of the phone frame after removing the screen. This will prepare the area for reinstalling the display later.

---

Step 3: Remove the Graphite Tape and Board Bracket

Release the graphite tape to access the board bracket.

Next, remove the ten screws holding the board bracket.

Two additional screws with a small shield are located above the charging port board. Peel back the tape covering this area, remove the two screws, and pull out the bracket.

Once all the screws have been removed, gently pull the board bracket out of the phone body.

[INTERNAL LINK: Related repair guide]

---

Step 4: Disconnect the Battery and Rear Camera

Disconnect the battery plug from the board.

Next, disconnect the two rear camera connector plugs from the board.

With the camera connectors disconnected, remove the screw securing the rear camera unit.

---

Step 5: Remove the Faulty Rear Camera

After removing the securing screw and disconnecting both camera connectors, gently pull the non-working rear camera unit away from the board.

Handle the camera assembly carefully during removal and avoid unnecessary force.

Once the faulty camera has been removed, the replacement camera can be installed.

---

Step 6: Install the New Rear Camera

Place the replacement rear camera unit into position.

Secure the camera unit with its screw.

Next, reconnect both camera connector plugs to the board.

Make sure the camera unit and its connectors are properly positioned before continuing with the reassembly.

---

Step 7: Reconnect the Battery and Board Bracket

Reconnect the battery plug to the board.

Next, place the board bracket back into position.

Secure the board bracket using the ten screws removed earlier.

Remember to reinstall the small shield when adding the two screws above the charging port board.

---

Step 8: Test the Rear Camera

Before permanently securing the display, reconnect the screen for testing.

Test the phone and confirm that the replacement rear camera is functioning correctly.

Once the testing has passed, disconnect and remove the screen again so it can be permanently secured.

---

Step 9: Apply Adhesive to the Display

Before reinstalling the LCD screen, make sure there is enough adhesive available to secure it properly.

You can use B7000 glue or new double-sided LCD adhesive. In this repair, B7000 glue is used.

Apply the adhesive as required before reinstalling the display.

---

Step 10: Reconnect and Install the LCD Screen

Reconnect the LCD connector and then reinstall the connector bracket.

Carefully slide the screen into position, starting from the left and moving toward the right.

Once the display is aligned correctly, gently apply pressure around the edges of the screen to secure it against the phone body.

---

Step 11: Secure the Display

Use bonding clips to hold the LCD screen firmly against the phone while the adhesive sets.

Leave the clips in place for some time before removing them.

If bonding clips are not available, rubber bands can be used to hold the display tightly against the phone body while the adhesive sets.

End of Repair Guide

The Google Pixel 5 rear camera replacement is now complete. Once the display adhesive has set, power on the phone and test the rear camera to make sure it is working correctly.

---

FAQ

Does the Pixel 5 screen need to be removed for a rear camera replacement?

Yes. This repair procedure begins by removing the display so the internal camera connections and board bracket can be accessed.

How many camera connectors need to be disconnected?

The repair procedure requires disconnecting two camera connector plugs from the board before removing the rear camera unit.

Does the battery need to be disconnected?

Yes. The battery plug is disconnected before the camera replacement and reconnected during reassembly.

How is the rear camera secured?

The rear camera unit is held in place with a screw in the repair procedure. Both camera connector plugs are also reconnected after the replacement unit is installed.

Should I test the camera before permanently installing the screen?

Yes. The screen is connected temporarily for testing before it is removed again and permanently secured with adhesive.

---

Troubleshooting

The replacement rear camera is still not working. What should I check?

Check that both camera connector plugs have been properly connected to the board. Also make sure the replacement camera unit is correctly positioned and secured.

The display does not work after the repair. What should I check?

Recheck the LCD connector and make sure it is properly connected. Confirm that the LCD connector bracket is also installed correctly.

The display is lifting after reinstallation. What should I do?

Check that enough B7000 glue or double-sided LCD adhesive was used. Hold the screen firmly against the phone with bonding clips or rubber bands while the adhesive sets.

The board bracket does not sit correctly. What should I check?

Make sure the bracket is correctly positioned and that the screws and small shield above the charging port board have been reinstalled correctly.

Can I skip testing before installing the screen permanently?

It is better to follow the repair procedure and test the phone while the display is temporarily connected. This lets you confirm that the replacement camera is working before securing the screen with adhesive.

Related Guides

Pixel 4 Repair Guides

Pixel 6A Battery Replacement guide

More Pixel 5 Repair Guides